Middle East Department
Housing Brackets

• Extension for MOBOTIX cameras
• Microphone/speaker
• PIR sensor for motion detection, temperature sensor
• Integrated switch functions

• Set consisting of pole mount (MX-OPT-MH) and wall mount (MX-OPT-WH)
• Pole Mount for fastening of Dome wall mount
• 3 mm stainless steel, white
• Delivery with 2 stainless steel straps for pole diameters of 60 - 180 mm as well as mounting parts
• Wall mount is weather-proof (IP65) for protection of D22/D24 MonoDome
• Covers RJ45 wall outlets
• Space for expansion modules (battery, UMTS, WLAN, etc.)

• Consists of on-wall mount and mounting parts
• Also conforms to U.S.installation standards
• Reliably protects the cabling and allows integrating additional modules within the on-wall mount
• Dimensions: 165 mm x 37 mm

The On-Wall set can reliably protect external cables if the cables cannot be guided from below the housing but have to be led above the wall. In addition, the On-Wall mount provides ample space for extra modules.

• Consists of on-wall mount and mounting parts
• Also conforms to U.S.installation standards
• Reliably protects the cabling and allows integrating additional modules within the on-wall mount
• Dimensions: 166 mm x 74 mm

The On-Wall set allows the mounting of the camera at a 10 Degrees tilt angle. Moreover, it reliably protects external cables if the cables cannot be guided from below the housing but have to be led above the wall. In addition, the On-Wall mount provides ample space for extra modules.

• Fastening for Dome wall mount MX-OPT-WH
  (for D22/D24 IT/Sec, Q22/Q24 Sec and ExtIO)
• 3 mm stainless steel, white
• Delivery includes mounting parts and 2 stainless steel straps for pole diameters of 60 - 180 mm
• Wall mount (MX-OPT-WH) is not included in delivery and has to be ordered separately
• Alternatively, a set consisting of pole mount (MX-OPT-MH) and wall mount (MX-OPT-WH) is available

If you would like to mount either the MOBOTIX D22/D24 IT/Sec, Q22/Q24 Sec or ExtIO to a pole, you should consider using the MOBOTIX Pole Mount. This mount can only be used in conjunction with the wall mount. The supplied stainless steel straps allow attaching the mount to poles with diameters between 60 and 180 mm. The Pole Mount is made from 3 mm white powdercoated stainless steel and is just as robust and maintenance-free as the outdoor Wall Mount.

• Consists of in-ceiling mount and mounting parts
• Easy mounting from front
• Installation dimension: 150 mm

• Weatherproof (IP65) wall mount for MOBOTIX dome cameras D22/D24 IT/Sec, Q22/Q24 Sec and ExtIO
• Covers RJ45 wall outlets
• Space for expansion modules (battery, UMTS, WLAN, etc.)
• Easily mounted to poles using pole mount

The Wall Mount is the ideal solution for mounting MOBOTIX dome cameras D22/D24 IT/Sec, Q22/Q24 Sec or ExtIO to walls for indoor and outdoor applications. The camera is absolutely dustproof and resistan against water jets (IP65). The wall mount also covers RJ45 wall outlets and has ample space for additional modules.

• In-Ceiling Mount for ATD-1000 PTZ Camera
• Provides a flush surface mount for PTZ, only the bubble shows through the ceiling
• Includes: Power Supply, Cables, Base Board, Housing and Bubble Dome Cover

• Solid end walls permit drilling to job specific requirements.
• Can be used to house encoders, decoders, transmitters/receivers, POE injectors, etc.
• 8" X 10" X 4" inside dimensions

• Outdoor / Indoor - Camera Housing
• Nylon + Fiber Glass in Beige
• Certificate: CE
• Appearance: 151mm (W) x 145mm (H) x 390mm (L)
• Suitable Camera: 95mm (W) x 80mm (H) x 250mm (L)
• Optional Accessories: Heater, Blower, IR LED
• 12VDC / 24VAC / 110VAC / 220 VAC
• Package: 8 pcs / ctn / 630mm x 405mm x 340mm
• IP-66 Rating
• Cable Thru Wall Mount
• Work with VHM-208 & VHM-209

• Construction: Aluminum coated black/white optional
• Max Load 2kg
• Height: 225mm
• Base size:100 x 80 x 3mm
• Swivel angle 360 Degrees
• Weight 1075gm
• Tilt angle 180 Degrees

• 61/2' Extension size
• Beige color

Wall mount Bracket for most Indoor Plastic Dome Cameras

• Mounting Bracket with T-BAR

Mounting Bracket 2 Point Swivel Function

Mounting Bracket with T-BAR

• Medium size metal mounting bracket for TFT Monitors, Telescope, Cameras

• Heavy duty, steel construction
• Integral J-Box mounting plate with 0.625" round cable pass thru hole
• Includes three adjusting knuckles
• Knob and tamper-resistant set-screw adjusting options included with each knuckle

• Flexible mount, 16" long
• Double wound shaft will not droop or require safety wires
• Shaft is covered with durable black vinyl
• Knob and tamper-resistant set-screw adjusting options are included
• The base accepts the shaft in a vertical or horizontal position

• Adjustable shaft
• Adjusts from 9.375 inches to 13.625"
• Knob and tamper-resistant set-screw adjusting options included

• Hollow aluminum shaft with slot for cable pass through
• Knob and tamper-resistant set-screw adjusting options included
• Integral J-Box mounting plate
• 6" overall length from base to top of lock-ring

• Hollow aluminum shaft for cable pass through
• Knob and tamper-resistant set-screw adjusting options are included

• This bracket attaches to 3/4" conduit and is used to make long ceiling drops.
• For cameras weighing up to five lbs.
• Includes both knob and set-screw adjusting options

• Knob and tamper-resistant set-screw adjusting options are included
• 0.5" diameter solid steel shaft
• Length of mount from base to front of mount is 4"
• Length of mount from bottom of angle to top of mount is 3.4"
• 1/4-20 stud with lockring, adjustable at the camera.
• Knob and tamper-resistant set-screw adjusting options are included
• Matching vinyl cover adds a finished look
• 2" round base

• This bracket mounts on 3/4" conduit and is used to make long ceiling drops
• For cameras weighing up to 3 lbs.
• Includes both knob and set-screw options

• Magnet holds up to 5 lbs.
• Base is 2.75" in diameter
• 1/4-20 Mounting stud

• Includes bolt holes and strap slots
• Will mount to poles of at least 1.25" in diameter
• Strap slots will accept straps up to 0.75" wide

• Our most versatile mount. Twelve different configurations with one unit
• Solid steel shafts
• Knob and tamper-resistant set-screw adjusting options are included
• Matching vinyl cover adds a finished look

• Adds 3" to the length of the 854-3-4 conduit mount

• Will fit on a standard single gang electrical box
• Cable pass through hole is 0.625 inches and will allow a standard BNC connector to pass through.
• Use this plate with  #845-246 and #883T mounts

• Listed here for replacment purposes.  This clip is included with the 845-246 Deluxe Micro Mount

• Easy installation and a service friendly structure
• Interface for the connections of ext. sensors, devices (door contact, light, etc.)
• 2 x relays (230V/500W)
• 2 x input, backup, audio

• Easy installation and a service friendly structure
• Interface for the connections of ext. sensors, devices (door contact, light, etc.)
• 2 x relays (230V/500W)
• 2 x input, backup, audio

• Easy installation and a service friendly structure
• Interface for the connections of ext. sensors, devices (door contact, light, etc.)
• 2 x relays (230V/500W)
• 2 x input, backup, audio

• All aluminum, gauge 11, alloy #3105H14
• 3/16' clear polycarbonate
• Abrasive resistant
• Cover Locked by 3 security hex socket screws
• White Finish polyurethane coating
• 1.5 lb (0.7 kg)

• 90 Degree Night Vision illumination
• 84 IR LEDs / Switched on/off by cell

• Outdoor / Indoor - Camera Housing
• Nylon + Fiber Glass in Beige
• Certificate: CE
• Appearance: 151mm (W) x 145mm (H) x 390mm (L)
• Suitable Camera: 95mm (W) x 80mm (H) x 250mm (L)
• Optional Accessories: Heater, Blower, IR LED
• 12VDC / 24VAC / 110VAC / 220 VAC
• Package: 8 pcs / ctn / 630mm x 405mm x 340mm
• IP-66 Rating
• Cable Thru Wall Mount
• Work with VHM-208 & VHM-209

• Outdoor / Indoor - Camera Housing
• Nylon + Fiber Glass in Beige
• Certificate: CE
• Appearance: 151mm (W) x 145mm (H) x 390mm (L)
• Suitable Camera: 95mm (W) x 80mm (H) x 250mm (L)
• Optional Accessories: Heater, Blower, IR LED
• 12VDC / 24VAC / 110VAC / 220 VAC
• Package: 8 pcs / ctn / 630mm x 405mm x 340mm
• IP-66 Rating
• Cable Thru Wall Mount
• Work with VHM-208 & VHM-209

• Outdoor / Indoor - Camera Housing
• Nylon + Fiber Glass in Beige
• Certificate: CE
• Appearance: 151mm (W) x 145mm (H) x 390mm (L)
• Suitable Camera: 95mm (W) x 80mm (H) x 250mm (L)
• Optional Accessories: Heater, Blower, IR LED
• 12VDC / 24VAC / 110VAC / 220 VAC
• Package: 8 pcs / ctn / 630mm x 405mm x 340mm
• IP-66 Rating
• Cable Thru Wall Mount
• Work with VHM-208 & VHM-209

• Wall Bracket for Mag-CD600

Quickly and Easily Mount any VESA? LCD TV/ Monitor
Low-Profile Design
Fast, Simple Wall Mounting
Meets VESA? Standards (75x75mm and 100x100mm)
Load up to 33 lbs / 15 kgs*
Includes Stud Mount Wall Plate, Monitor Plate and Hardware Kit
Fully Adjustable and Viewable at any angle
Powder Coated, Brushed Aluminum Construction
Packaged in Attractive Display Box

FLAT-PANEL CCTV MONITOR BRACKET FOR MONITORS 10? - 30?
FITS STANDARD VESA? MONITORS 50mm / 75mm / 100mm
MAXIMUM WEIGHT 44 LBS.
EXTENDABLE CEILING POLE CAN LOWER
ADJUSTABLE HEAD CAN ROTATE 190?
ADJUSTABLE HEAD CAN PIVOT ? 20?
ABS PLASTIC AND BRUSHED ALUMINUM CONSTRUCTION
BLACK COLOR

• For Vesa Mounting 50x50, 75x75x, 10x100mm
• Adjustable tilt 15* up and down
• Swivel Lweft and Right
• Max clearence from wall 13cm
• Supports up to a 22.7 kg (501lbs) load
• LCD Monitor swivel 360*
• Hardware included 

• LCD TV / Monitor Flat Panel Flush Mount Wall Bracket
• Not to exceed 66 LB (30 KG) Weight Limit

(Pole Diameter of 5' to 10') 8' Wide

for AS75W and AH75WP

for CG30 and CG31 (Mini B/W Camera)

• 1 year parts and labor warranty

• Indoor or outdoor use
• Side opening
• 17" Overall length
• Enclosure will accommodate a camera/lens combination of up to 7" in length
• Includes heater & blower  (Requires 24 VAC, 12 VA)

6' Pod fits full body cameras in a ceiling Dome mount. Allows for any camera and Lens combination.

Dimensions 14' x 5' x 4'

Dimensions 14' x 5' x 4'

4.75' Dome Housing (No Camera)